Pompe Solare - pompa ecologica pentru apa

 

1. Pompe solare - seria Lorentz

 

PS150 C-SJ5-8
Model LPP00057
lift[m] 0-22
max.flow rate [m3/h] 5.0
max. efficienty [%] 45
solar operation

nominal valtage 12-24 V DC 

open circuit voltage max. 50 V DC

solar generator[Wp] 65-450
battery operation nominal voltage 12-24 V DC

Overview

  • lift up to 22 m
  • flow rate up to 5.0 m3/h
  • charger for 12/24 V batteris and MPPT booster for solar-direct application included
  • simple installation
  • maintenance free
  • high reliability and life expectancy
  • cost-efficient pumping

2 years manufacturer's warranty against defects in material and workmanship

Applications

  • drinking water supply
  • livestock watering
  • pond management
  • irrigation

etc.

 

Controller PS150

  • controlling of the pump system and monitoring of the operating states
  • charge controller included
  • mounted at surface (no submerged electronic parts)
  • two control inputs for well probe (dry running protection), float or pressure switches, remote control etc.
  • automatic reset 20 minutes after well probe turns pump off
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 88 % (motor + controller)
enclosure: IP 54 (sealed, weatherproof

Motor ECDRIVE 200 C

  • brushless DC motor
  • water filled
  • dynamic slide bearings, material: carbon/ceramic
  • wetted material: stainless steel (AISI 316), POM, rubber, cable drinking water approved

 

Pump end (PE)

  • high life expectancy
  • none-return valve
  • dry running protection (optional)
material: stainless steel (AISI 316), rubber

 

PS200 HR-04 HR-07 HR-14 C-5-4
Model LPP00028 LPP0029 LPP00030 LPP0031
lift[m] 0-50 0-30 0-20 0-15
max. flow rate [m3/h] 0.8 1.2 2.7 5.0
max. efficiency[%] 60 61 62 45
salor operation

nominal voltage 24-48 V DC

open circuit voltage max. 100 V DC

battery operation

ony

solar generator [Wp] 80-300 80-300 80-300  
battery operation nominal voltage 24-48 V DC

Overview

  • lift up to 50 m
  • flow rate up to 2.7 m3/h (HR) resp. 5.0 m3/h (C)
  • simple installation
  • maintenance free
  • high reliability and life expectancy
  • cost-efficient pumping
  • 2 years manufacturer's warranty against defects in material and workmanship

Controller PS200

  • controlling of the pump system and monitoring of the operating states
  • mounted at surface (no submerged electronic parts)
  • two control inputs for well probe (dry running protection), float or pressure switches, remote control etc.
  • automatic reset 20 minutes after well probe turns pump off
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 88 % (motor + controller)
  • enclosure: IP 54 (sealed, weatherproof)

Applications

  • drinking water supply
  • livestock watering
  • pond management
  • irrigation etc.

Motor ECDRIVE 600 HR / 200 C

  • brushless DC motor
  • water filled
  • dynamic slide bearings, material: carbon/ceramic
  • wetted material: stainless steel (AISI 316), POM, rubber, cable drinking water approved

 Pump end (PE)

  • high life expectancy
  • none-return valve
  • dry running protection (optional)
  • material: stainless steel (AISI 316), rubber

 for HR pumps only

  • helical rotor pump (positive displacement pump)
  • two main parts only: stator and rotor, field servicable
  • stator: geometry made of abrasion resistant rubber
  • rotor: stainless steel, hard chrome plated, abrasion resistant
  • more resistant to damage by sand than other pump types self-cleaning

 

PS600 HR-03 HR-03H HR-04 HR04H
Model LPP0032 LPP00033 LPP0034 LPP0035
lift[m] 0-140 140-180 0-80 80-140
max. flow rate [m3/h] 0.5 0.5 0.8 0.8
solar operation nominal voltage 48-72 V DC
open circuit voltage max. 150 V DC
solar generator [Wp] 300-480 420-900 300-480 420-900
battery operation        
  nominal voltage 48 V DC

 

PS600

HR-07

HR-10

HR-14

HR-20

Model

LPP00036

LPP00037

LPP00038

LPP00039

lift [m]

40-90

30-60

0-50

0-30

max. flow rate [m3/h]

1.2

1.9

2.7

3.6

max. efficiency [%]

64

64

65

64

solar operation

nominal voltage 48-72 V DC
open circuit voltage max. 150 V DC

solar generator [Wp]

420-900

420-900

300-900

420-900

battery operation

nominal voltage 48 V DC

 

PS600

C-SJ5-8

C-DF-03

Model

LPP00040

LPP00041

lift [m]

0-20

0-10

max. flow rate [m3/h]

7.3

11

max. efficiency [%]

40

40

solar operation

nominal voltage 48-72 V DC
open circuit voltage max. 150 V DC

solar generator [Wp]

300-900

720-900

battery operation

nominal voltage 48 V DC

 

Overview

  • lift up to 180 m
  • flow rate up to 11 m3/h
  • simple installation
  • maintenance-free
  • high reliability and life expectancy
  • cost-efficient pumping
  • 2 years manufacturer's warranty against defects in material and workmanship

Controller PS600

  • controlling of the pump system and monitoring of the operating states
  • mounted at surface (no submerged electronic parts)
  • two control inputs for well probe (dry running protection), float or pressure switches, remote control etc.
  • automatic reset 20 minutes after well probe turns pump off
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 92 % (motor + controller)
  • enclosure: IP 54 (sealed, weatherproof)

Applications

  • drinking water supply
  • livestock watering
  • pond management
  • irrigation

etc.

Motor ECDRIVE 600 HR / C

  • brushless DC motor
  • water filled
  • IP 68, pressure balanced, max. submersion unlimited
  • dynamic slide bearings, material: carbon/ceramic

wetted material: stainless steel (AISI 316), POM, rubber, cable drinking water approved

Pump end (PE)

  • high life expectancy
  • none-return valve
  • dry running protection (optional)
  • material: stainless steel (AISI 316), rubber

for HR pumps only

  • helical rotor pump (positive displacement pump)
  • two main parts only: stator and rotor
  • stator: geometry made of abrasion resistant rubber
  • rotor: stainless steel, hard chrome plated, abrasion resistant
  • more resistant to damage by sand than other pump types self-cleaning

PS1200

HR-03

HR-03H

HR-04

HR-04H

Model

LPP00042

LPP00043

LPP00044

LPP00045

lift [m]

0-140

140-240

0-80

80-160

max. flow rate [m3/h]

0.5

0.5

0.8

0.8

max. efficiency [%]

60

64

60

65

solar operation

nominal voltage 72-96 V DC
open circuit voltage max. 200 V DC

solar generator [Wp]

350-480

420-900

350-420

420-1200

battery operation

nominal voltage 72-96 V DC

 

PS1200

HR-07

HR-10

HR-14

HR-20

Model

LPP00046

LPP00047

LPP00048

LPP00049

lift [m]

40-120

30-80

0-60

0-40

max. flow rate [m3/h]

1.2

1.9

2.7

3.6

max. efficiency [%]

64

64

65

64

solar operation

nominal voltage 72-96 V DC
open circuit voltage max. 200 V DC

solar generator [Wp]

420-1200

420-1200

350-1200

480-1200

battery operation

nominal voltage 72-96 V DC

PS1200

C-BF-04

C-DF-03

 

Model

LPP00050

LPP00051

 

lift [m]

0-25

0-15

 

max. flow rate [m3/h]

7.3

11

 

max. efficiency [%]

40

40

 

solar operation

nominal voltage 72-96 V DC
open circuit voltage max. 200 V DC

 

solar generator [Wp]

350-1200

840-1200

 

battery operation

nominal voltage 72-96 V DC

 

 

Overview

  • lift up to 250 m
  • flow rate up to 51 m3/h
  • simple installation
  • maintenance-free
  • high reliability and life expectancy
  • cost-efficient pumping

2 years manufacturer's warranty against defects in material and workmanship

Controller PS1800

  • controlling of the pump system and monitoring of the operating states
  • mounted at surface (no submerged electronic parts)
  • two control inputs for well probe (dry running protection), float or pressure switches, remote control etc.
  • automatic reset 20 minutes after well probe turns pump off
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 92 % (motor + controller)
  • enclosure: IP 54 (sealed, weatherproof)

Applications

  • drinking water supply
  • livestock watering
  • pond management
  • irrigation

etc.

Motor ECDRIVE 1800 C

  • brushless DC motor
  • no electronic parts in the motor
  • water filled
  • IP68, pressure balanced, unlimited submersion
  • dynamic slide bearings, material: carbon/ceramic
  • wetted material: stainless steel (AISI 316), POM, rubber, cable drinking water approved

 Pump end (PE)

  • high life expectancy
  • none-return valve
  • dry running protection (optional)

material: stainless steel (AISI 316), rubber

 

 

 

 

Cod

MODEL

Lift [m]

Flow Rate [m3/h]

LPP00064

PS4000

C-SJ3-32

130– 170

3,3– 3,8

LPP00065

PS4000

C-SJ5-25

70– 130

4,3– 6,6

LPP00066

PS4000

C-SJ8-15

30– 80

6,9– 12,2

LPP00067

PS4000

C-SJ17-4

15– 50

14– 24,5

LPP00068

PS4000

C-SJ30-2

12– 22

33– 44

LPP.........

PS4000

C-SJ42-1

max 12

44– 70

 

Total Lift

PS150 Boost 60

PS150 Boost 125

PS150 Boost 240

Model

LPP00052

LPP00053

LPP00054

[m]

[l/h]

[W]

[l/h]

[W]

[l/h]

[W]

5.0

260

35

480

50

900

65

10

260

40

470

55

900

90

15

250

45

470

62

890

105

20

250

55

470

70

880

120

25

250

63

460

80

880

135

30

250

72

450

90

870

150

40

250

80

450

105

870

200

45

240

85

450

112

860

225

50

240

90

450

120

 

 

60

240

95

430

140

 

 

70

240

110

420

160

 

 

80

240

125

410

185

 

 

90

240

140

410

200

 

 

100

230

165

 

 

 

 

120

230

185

 

 

 

 

140

220

220

 

 

 

 

LORENTZ PS150 Boost provides city water pressure, anywhere. It has been a standard in home renewable energy systems since 1986. It is economical for domestic water supply, drip irrigation and water purification. Use solar-electric power to provide 250 to 10,000 litres per day from shallow water sources. PS150 Boost can push water as high as 140 m.

For 12 V to 24 V systems (1-2 solar modules or batteries in series) uses only one and the same motor and controller for solar direct or battery systems. Same flow at 12 V or 24 V.

LORENTZ PS150 Boost is not submersible, but can draw water from shallow wells, springs, cisterns, tanks, ponds, rivers and streams and push it through miles of pipeline. Slow pumping minimizes the size and cost of the solar array-battery system, wire and piping.

LORENTZ PS150 Boost is more powerful, quieter and much more durable than plastic RV/Marine pumps. It is less expensive than submersible DC pumps. Wearing parts typically last 5 to 10 years. Overall life expectancy is 15 to 20 years.

Suction Capacity

5 m (15 ft) at sea level. Subtract 1 m (3 ft) for every 1,000 m (3,300 ft) altitude. Pump should be placed as low and as close as possible to the water source. Suction capacity my be further limited by intake pipe friction (or clogged filter).

Intake piping should be 1” or larger.

Filtration Requirement

This pump cannot tolerate dirt. Water must be filtered clear. If water is very dirty, improve the source or consider a different pump.

PV-Direct (non-battery) Requirements

  • The rated power of the PV array must exceed pump watts by 20 % or more.
  • A linear current booster incl MPPT (maximum power point tracking) is already included !
  • Solar Tracker (optional) will increase daily yield (40-55 % in summer)

 Installation

  • Pump may be mounted horizontally or vertically.
  • Pump must not be submerged
  • It may be placed inside a 6” (120 cm) or larger well casing, suspended by a rope

Short Overview

  • solar operated surface vane type pump
  • max lift up to 120 m
  • max. flow rate 0.9 m3/h
  • simple installation
  • high reliability and life expectancy
  • cost-efficient pumping
  • wetted materials: stainless steel, brass, rubber, plastic

 

Applications

  • drinking water supply
  • water purification and filtration
  • pressurizing for home water systems
  • drip irrigation
  • water circulation in thermal solar collectors (max. +60oC, +90 oC on request)

etc.

Accessories

  • Inline Filter: (10”) Uses standard filter cartridges
  • Installation Kit includes: Pressure switch, pressure gauge, check, drain and shut-off valves and tank tee.
  • Float switch for tank shut off if full.
  • Well probe sensor to protect pump from dry-running.

 

Dimensions

  • Pump Unit
    • Length: 33 cm (13”)
    • Weight: 7.0 kg (15 lb)
  • Controller
    • 260 x 175 x 100 mm (10" x 7" x 4")
    • Weight: 1.5 kg (3.6 lb)

 

Warranty

1 year against defects in materials and workmanship

 
 
 
Pompe de suprafata

 

 

 

 

 

 

 

Pump System

                                 PS200 AIR

 

 

 

 

 

 

 

Model

LPP00055

max. differential pressure [bar]

0.6

max. flow rate [m3/h]

4.0

solar operation

nominal voltage 24-48 V DC
open circuit voltage max. 100 V DC

solar generator [Wp]

80-250

battery operation

nominal voltage 24-48 V DC

Overview

  • for air pumping
  • differential pressure up to 0.6 bar (air)
  • flow rate up to 4.0 m3/h (air)
  • simple installation
  • maintenance-free
  • high reliability and life expectancy
  • cost-efficient pumping

Motor ECDRIVE 200 AIR

  • brushless, maintenance-free DC motor

 

Controller PS200

  • controlling of the pump system and monitoring of the operating states
  • mounted at surface (no submerged electronic parts)
  • two control inputs for pressure switches, remote control etc.
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 88 % (motor + controller)
  • enclosure: IP 54 (sealed, weatherproof)
 

Applications

  • pond ventilation
  • oxygen enrichment of water
  • etc.

 

 

 

PS600 BADU Top12

Solar Operation

Battery Operation

max. flow rate [m3/h]

15

13

max. lift [m]

14

13

ambient temperature [oC]

-30 to +45

Controller

PS600

input voltage

solar generator:
nominal voltage
48-72 V DC
open circuit voltage
max. 150 V DC

battery, DC source:
nominal voltage
48 V DC

type of enclosure

IP 54

dimensions (net/packing)

395 x 175 x 165 mm / 450 x 250 x 250 mm
= 0.027 m3

weight (net/gross)

4.5 kg / 5.3 kg

Motor

ECDRIVE 600 BADU Top

max. power input [W]

600

type of enclosure

IP X4

class of insulation

F

Pump End

BADU Top 12 (manufacturer Speck Pumps)

suction / max. positive inlet lift

3.0 m

max. casing pressure

2.5 bar

max. water temperature

+60 oC

Motor + Pump End

ECDRIVE 600 BADU Top + BADU Top 12

dimensions (net / packing)

see dimension drawing:
520 x 220 x 350 mm
= 0.0400 m3

weight (net / gross)

8.7 kg / 9.7 kg

 

 

Overview

  • surface centrifugal pump for solar operation
  • flow rate up to 15 m3/h
  • simple installation
  • maintenance-free thanks to brushless DC motor
  • high reliability and life expectancy
  • cost-efficient pumping
  • 2 years manufacturer's warranty against defects in material and workmanship

Applications

  • swimming pool water circulation through a filter system and thermal collectors
  • pond management
  • irrigation
  • aquariums
etc.a

 

Pump System

PS600 BADU Top 12

Model

LPP00056

controller

PS 600

motor

ECDRIVE 600 BADU Top

pump end (PE)

BADU Top 12
(manufacturer Speck Pumps)

source of energy
(not included in delivery)

solar generator (340-900 Wp)
battery, DC source

 

Pump end (PE) BADU Top 12

  • monoblock-type pump with integrated strainer tank
  • bellow mechanical seal is mounted on a plastic shaft protected sleeve
  • motor/pump shaft has no contact with fluid
  • total electric separation
  • strainer capacity approx. 3 l
  • strainer basket mesh size approx. 3.2 x 2.6 mm

Material used for pump end

  • pump casing, strainer basket: PP
  • flange, gland housing: PP TV 40
  • diffuser: PP TV 40
  • impeller: PA 66 GF 30 / PC
  • lid: PC, transparent
  • mechanical seal: carbon / ceramic / NBR
  • bolts: steel, galvanized

Motor ECDRIVE 600 BADU Top

  • brushless, maintenance-free DC motor

 

Controller PS600

  • controlling of the pump system and monitoring of the operating states
  • mounted at surface (no submerged electronic parts)
  • two control inputs for well probe (dry running protection), float or pressure switches, remote control etc.
  • automatic reset 20 minutes after well probe turns pump off
  • protected against reverse polarity, overload and high temperature
  • speed control, max. pump speed adjustable to reduce flow rate to approx. 30 %
  • solar operation: integrated MPPT (Maximum Power Point Tracking)
  • battery operation: low voltage disconnect and restart after battery has recovered
  • max. efficiency 92 % (motor + controller)

Pompa Solara LJ

Pompele cu fiabilitate ridicata fara motor circular. Nu e necesar folosirea unei baterii. Aceasta pompa nu necesita intretinere si functioneaza cu un panou solar mic de 12 W , fara probleme. Este foarte utila pentru pomparea apei potabile, apa pentru incalzire solara, apa necesara unui dus de plaja si pentru irigarea gradinii. Aceasta pompa functioneaza cu energie solara pe tot parcursul zilei. Este o pompa cu debit scazut si nu sunt probleme care pot aparea din cauza nisipului.

 

Cod Produs

LPP00010

Model

LJ10

Solar Pump

 

Putere

12W

Tensiune alimentare

12V

Dimensiune

50x25x20 cm

Greutate

5,2 kg

Adancimea maxima

10m

 Germania

 

 

 

Cod Produs

LPP00011

Model

LJ20

Solar Pump

 

Putere

12W

Tensiune alimentare

24V

Dimensiune

50x25x20 cm

Greutate

5,2 kg

Adancimea maxima

20m

 Germania

 

 

Pompa Solara Spring

Pompa Solara Spring submersibila cu ax-piston orizontal. La o putere de doar 200W, foloseste energia necesara a unui bec pentru a scoate apa de la o adancima mai mare de 100m. Are un motor care poate fi racit cu aer si deci poate functiona in gol. Doua pistoanecu un diametru de 40 mm, echilibrate , functioneaza prin “bataie” la o frecventa de pana la 3000rpm. Capacitatea de pompare este de 11m3/zi si poate fi considerate cea mai avansata tehnologie de pompare solara din lume.

 

Cod Produs

LPP00008

Model

SSP

Solar Pump SSP

Putere

0W-200W

Tensiune alimentare

24V-80V

 

 

Greutate

14kg

Adancimea maxima

max. 250m

 Germania

 

Pompa Solara SQ Flex

Instalarea SQFlex Solar nu necesita nici un echipament special ci doar cuplarea directa la panouri solare. Este economica si nu necesita intretinere. Dispune de protectie impotriva functionarii in gol, supraincarcare si supraincalzire. Reporneste automat in prezenta apei sau cand temperatura motorului scade la limita normala. Dispune de monitorizare automata a sarcinii si a tensiunii de alimentare.

 

 

 

 

 

 

SQ Flex pentru uz orizontal si vertical

incl. Motor MSF3 1 x 90-240V, Rp 11/4

Solar Pump SSP

-10%/+6%, 50/60 Hz, 2m cablu de motor

cu sistem integrat MPP-Tracking

 

Danemarca

Cod Produs

Model

Dimensiune (mm)

Greutate (Kg)

LPP00013

SQ Flex 1.2-2

1225x74

9,7

LPP00014

SQ Flex 0.6-2

1185x74

9,4

LPP00015

SQ Flex 2.5-2

1247x74

10

LPP00016

SQ Flex 5A-3

815x101

9,6

LPP00017

SQ Flex 5A-6

875x101

10,3

LPP00018

SQ Flex 8A-3

920x101

11

LPP00019

SQ Flex 14A-3

975x101

12,4

 

Pompe solare Shurflo 9300

Pompele Shurflo's 9300 sunt produsul a 25 de ani de experienta in domeniu. Construit pentru a fi puternic si usor in acelasi timp aceste pompe au fost concepute pentru aplicatii ca irigatii sau acumulare de apa in bazine pentru uz casnic. Pentru acest tip e necesar un controler de pompa sau poate fi cumparat un set complet care include un 902-200 controler Shurflo.

 

Cod Produs

LPP00020

Dimension

95x305 mm

 

Weight

3,2 kg

USA

Deplasament pozitiv cu diafragma in 3 camere

Motor: magnet permanent ,  protectie termica

24 volts DC, 4.1 amps maximum. (P/N 11-175-00)

Internal bypass:105-110 PSI

Adancime Max de ridicare: 230 feet (70 meters)

Adancime maxima: 100 feet (30 meters)

Teava de iesire t: 1/2" (12.7 mm) barbed fitting for 1/2" ID tubing

Intrare pe ecran din inox din 50 de plase

 

6. Pompa solara Shurflo 2088 12/24 V de presiune

Seria Shurflo 2088 de pompe este considerate “ caii de povara “ pentru sistemele mici de pompare pentru apa. Acestea sunt folosite in aplicatii unde e nevoie de un debit de pana la 13,6 litri/min. Aplicatile include irigatii de terenuri , alimetare bazine cu apa si aplicatile de pompare folsite la  barci sau iahturi. Acest pompe nu sunt concepute pentru folosire indelungata si conditii dure insa poate avea instalat un corp additional de racire de 4” (#34-007) pentru aceste aplicatii.

De asemenea dispune de protectie pentru mers in gol cat si de o valva de retinere a apei. Opereaza automat cu comutator la  presiune.

 

Shurflo Standard 8000-443-136

LPP00026

Heavy duty flow pump 12VDC, 30m, 6 l/min, 4 bar water pump, 1/2 MSPT port threads

1.8 GPM open flow, EPDM valves, Santoprene®diaphragm

 

60 PSI Demand Switch, 1/2" MPT-Male ports.

USA